Find Jobs
Hire Freelancers

Crouzet Controller for a heatpump

$1500-3000 USD

已关闭
已发布超过 11 年前

$1500-3000 USD

货到付款
We would like asap a quote for following project on a Crouzet Smart, heatpump application. Compressor heats boiler (55°C) and water for radiant heating (35°C) Inputs. 3 NTC probes (if 1 spare available, a 4th probe) 1 contact pressure protection. On/Off If spares input available: immediate heat boiler and/or immediate engage electrical heater to support radiant heating. Output. Compressor 3 way valve Electrical heater Circulation pump (water) The available M3 Crouzet function block Heating Curve is used to adapt the water temperature to the outside temperature. Electrical heater is used when radiant water doesn’t reach within a safety time preset temperature. Heating of the boiler is postponed till lower night rates or immediately heated by a push button. Once in a week, boiler is postheated by the electrical heater to avoid legionella. On the screen, we see (eventually by scrolling down) actual temperature boiler Actual temperature radiant water temperature Outside temperature discharge gas temperature Set value radiant Set value Boiler Actual hour User can alter on the screen (eventually by scrolling down) Set water and radiant temperature. Change clock. The amplification factor for the heating curve. If the heat pumps run only on the lower night rates or continuous (on programming level, we will say in the code when lower night rates can be used, Saturday and Sunday are also the whole day lower night rates in Belgium) When boiler will be heated (the radiant heating is stopped while we heat the boiler) System stops when discharge temperature reaches overtemperature (set on programming level) When radiant temperature is at set temperature, pump is stopped and compressors then runs some seconds longer (set on programming level) to pump down partially the system. What would be the additional cost to make it possible we can monitor this via the www? Kind regards Peter
项目 ID: 2791454

关于此项目

5提案
远程项目
活跃11 年前

想赚点钱吗?

在Freelancer上竞价的好处

设定您的预算和时间范围
为您的工作获得报酬
简要概述您的提案
免费注册和竞标工作
5威客以平均价$1,840 USD来参与此工作竞价
用户头像
Professional simulation domain expert engineer here.
$2,200 USD 在25天之内
4.4 (49条评论)
5.4
5.4
用户头像
Dear Sir, We are Reserach and Development company whose working area are : -Digital Motor Control -Analog Design -Electronic Design -Power Electronics -PCB design -Embedded system -Matlab -Simulation of hardware For each concept descriptions are as follows: Digital Motor Control: -3-phase induction motor vector control drive -Flux estimation algoritm generation -DSP(TMS320) implementation on motor drive -Low speed application -Torque and speed loop generation -Control algoritms Analog design -Low power distribution -Noissless special opamp based analog circuits -Analog filters -Orcad simulation of several circuits Electronic Design -RF transmitter and receiver -Bluetooh reader and transmitter -Magnetic reader Power Electronics -Implementation motor drive -AC/DC converter -DC-DC converter -Battery charger -Solar inverter -Renewable Energy simulations -Uninterruptle power supplies PCB design -Schematic design by Altium -PCB design by Altium -Power board design -SMPS board design Embedded system -PIC18,PIC24,PIC30 and dsPIC applications -Ardino -MSP430 -Atmel -DSP(Texas Instruments) -Renesas Matlab -Power Electronics simulation -Motor drive -Wind Energy -Solar Energy -Control applications Simulation of Hardware -Orcad Simulation(TI,National, Linear Tech, Maxim libraries) -LTI -National -Matlab Very important Note: References attached. Please look excel file to see projects which we made until now! Metin
$2,500 USD 在40天之内
4.8 (10条评论)
4.9
4.9
用户头像
Kindly see your mail box. Thanks.
$1,500 USD 在14天之内
5.0 (1条评论)
3.9
3.9
用户头像
I have experience in PLCs and I could design and implement ladder for you.
$1,500 USD 在14天之内
0.0 (0条评论)
3.4
3.4
用户头像
Hello, I am embedded system engineer and have very good experience.I can design and program according to ur requirements and provide you with documentation.
$2,000 USD 在16天之内
0.0 (0条评论)
0.0
0.0
用户头像
hello sir, I have my bachelors in mechatronics and doing my masters in robotics and automation in germany. If the project is to be done in belgium than i myself can come there at the place and give u the desired output by working right with u. I have experience in PLC programming at industrial level and would also be working in SCADA in coming days at an industrial level. The cost will depend on work, and time also on the work to be done, but i assure u the best quality of the work and as fast as possible from my side. regards tarang
$2,000 USD 在40天之内
0.0 (0条评论)
0.0
0.0

关于客户

BELGIUM的国旗
Zedelgem, Belgium
5.0
5
会员自9月 9, 2008起

客户认证

谢谢!我们已通过电子邮件向您发送了索取免费积分的链接。
发送电子邮件时出现问题。请再试一次。
已注册用户 发布工作总数
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
加载预览
授予地理位置权限。
您的登录会话已过期而且您已经登出,请再次登录。