Find Jobs
Hire Freelancers

small size Arduino board

$10-30 USD

已完成
已发布超过 5 年前

$10-30 USD

货到付款
I need a small size arduino with only D2 D3 D4 D5 pins holes. Need to be able to upload code trough the programming pins holes. Also need A4 A5, GND VCC holes. Make with less components than regular arduino board. Board size around 40x30mm Power 5volt 16mhz I dont know what is best to use a crystal or a resonator . So long the unit works, it will be the same for me. I have done this project many times and all, ALL where NON working units after payment was done. IF YOU CAN DO THIS PROJECT, PLEASE BID! If not, dont bid! IT IS an requirement that it MUST be done in easyeda [login to view URL]
项目 ID: 18230112

关于此项目

10提案
远程项目
活跃5 年前

想赚点钱吗?

在Freelancer上竞价的好处

设定您的预算和时间范围
为您的工作获得报酬
简要概述您的提案
免费注册和竞标工作
颁发给:
用户头像
Hi, I have see your attachment. Actually it's not on your board fault. But I think you didn't downloaded a bootloader to your ATmega chip. ATmega chip that will be used as Arduino need to be downloaded by arduino bootloader before it can be used. And it needs to output AVR ISP pin(MOSI,MISO,SCK,RESET), and you need AVR ISP in order to do it. You can refer to arduino official web about it : [login to view URL] Once you download it bootloader to your AVR ATmega Chip, your arduino will be ready to used. And I think your board need to redesigned to output AVR ISP pin. Let me help you on it. Just add me to your easy EDA project and I will help you solve this. It just need a little bit modification and it only need a coople of hours to do it. I have used AVR since 2012 and I know both of its hardware and software issues. Let me help you fix this. Best Regards, Rijal
$30 USD 在5天之内
5.0 (23条评论)
4.6
4.6
10威客以平均价$68 USD来参与此工作竞价
用户头像
I have long experience with PCB design. I have worked with low-speed , high-speed and power boards. I use Altium Designer and Eagle, and I deliver neat layout that conforms to your dimension constraints and the manufacturing constraints. You can see samples of my previous work on my portfolio. More to be discussed once you contact me . BR, M.T.
$200 USD 在5天之内
4.8 (30条评论)
5.6
5.6
用户头像
Hello I have got your job posting “small size Arduino board” and I am very much interested to work in your project. I am a circuit designer and have more than 5 years experience of working with the Analog/Digital Electronics Embedded systems(Arduino,Rasberry pi ,ARM processors ,PIC microcontrollers,Wireless boards,TFT Touch Displays,PCB Board Designing,All types of sensors and actuators). i have done tons of similar projects So, I think you’ll find that, I have the skills you’re looking for. For more on my skills and successfully finished projects, please have a look on my Profile and Portfolio. I have a PCB developing facility available here with me so i will develop a working prototype according to your specifications and then send you the schematics and design files so things will work for sure. I am always available on Email and Skype. Please have a voice or video chat if necessary. I shall be available round the clock and able to start your project as soon as possible according to you. Thank you for your consideration, Best Regards, Haseeb Shafqat
$50 USD 在3天之内
4.8 (35条评论)
5.3
5.3
用户头像
Hi, I have experience with easyEda and with Atmega328, and I can build this for you. If you can send me the files done by other freelancers I can even edit or suggest you what could be going wrong with your PCBs. Thank you!
$100 USD 在4天之内
5.0 (11条评论)
4.7
4.7
用户头像
Hello Employer I can do it. I am experienced with Arduino for 3 years. I am Experienced with PCB designing with EAGLE for 2 years. I can do it in easyeda. For my different project I build my PCB Lay OUT for Arduino. Hope I can help you. Thank you.
$30 USD 在3天之内
5.0 (1条评论)
2.8
2.8
用户头像
I am an Electrical Engineer having specialization in Electronics Control and Power, teaching at well known University in Pakistan. I have my BS degree in Electrical Engineering with specialization in Power. Also i hire many persons in my Company for freelancing. They know many skills like Graphic designer, Logo Designer, Video Editing and Data entry. I have taught the followings courses, and also done many projects related to these subjects as well as related to consumer electronics products. 1. Control System Design & Modelling (Continuous, Discrete, Linear, Non-Linear, Optimal, Fuzzy Logic + Matlab & Simulink) 2. Digital System/Logic Design (Verilog, VHDL, Logisim) 3. Digital Signal Processing (MATLAB) 4. Micro-controllers (8051, Arduino, PIC) 5. Power Electronics (PSIM, MATLAB, PSpice) 6. Control of Electric Machine Drives 7. Circuit Analysis and Designe etc 8. PCB Design (Proteous + Ultiboard + Altium Designer) I assure you, if you assign your project to me, you surely gonna work with me in future. Note: I also provide the services in Mechanical Engineering and Computer Science related projects.
$25 USD 在1天之内
5.0 (3条评论)
1.6
1.6
用户头像
Hello, I have been using Arduinos and Atmega chips in my projects for years. It is possible to make it much smaller than you state also. I look forward to hearing from you. Kind regards, Hugo
$138 USD 在12天之内
0.0 (0条评论)
0.0
0.0
用户头像
Dear sir, I am an electrical engineer... I have much experience in aurdino and coding of aurdino.. I can do your project... please come a chat to discuss it.. Thanks
$25 USD 在2天之内
0.0 (0条评论)
0.0
0.0
用户头像
hi, bro. if you have that pcb which you shown in picture just try bootloader. and ya you also need to add powersupply unit for arduino.
$55 USD 在5天之内
0.0 (0条评论)
0.0
0.0
用户头像
I'm interested in the position of Small Size Arduino Board, particularly being from a PCB & Hardware Design. I've been working with ATMEGA328P standalone on my designs. I suggest to you use a resonator, it's smaller and doesn't need external components. I look forward to hearing from you soon — feel free to contact me directly to discuss the position further.
$25 USD 在2天之内
0.0 (0条评论)
0.0
0.0

关于客户

NORWAY的国旗
Fauske, Norway
5.0
14
付款方式已验证
会员自9月 29, 2017起

客户认证

谢谢!我们已通过电子邮件向您发送了索取免费积分的链接。
发送电子邮件时出现问题。请再试一次。
已注册用户 发布工作总数
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
加载预览
授予地理位置权限。
您的登录会话已过期而且您已经登出,请再次登录。