Find Jobs
Hire Freelancers

Embedded system -FPGA verilog code and do file using QUARTUS Prime lite,cyclone IV E

$10-30 AUD

已关闭
已发布超过 4 年前

$10-30 AUD

货到付款
Project: The project consists of multiple phases. It is to develop a waveform viewer (WV) that can send data to a PC for display. The data collection is done on the FPGA board. A microprocessor gets data from the FPGA board and sends data to the PC through either a Bluetooth modem or a USB port. The system supports three analog channels, with a single-level triggering. Only 8 bits of precision will be used for each analog channel. •Phase 1: Develop a minimal system that contains a PC, a UNO board, and an FPGA board. With this system, a PC application allows a user to “awaken” (or “start up”) the FPGA board through the microprocessor board. Only after the FPGA board is awakened, pressing down a push-button on the FPGA board requests the UNO board to send a character to the PC application which displays the character. You may use Termite as the PC application in this phase, but not in later phases. •Phase 2: Add a data source emulator to the minimal system. When requested by the FPGA board, the microprocessor board sends three channels of data to the PC. Each channel should contain N 8-bit values. (N is a constant to be determined in the lab and the coding should allow N to be changed easily.) The PC application will then graphically display the data. Use artificially generated data that can verify if the PC display works well. •Phase 3: Develop a simple WV system. (1)The FPGA board, once awakened, continuously collects data by using the on-board 3D accelerometer. The data are to be stored in a circular buffer. When the trigger occurs, the FPGA should continue to collect data in the buffer until one-quarter of the samples in the buffer occurred prior to the triggering and three-quarters after the triggering. These samples should then be sent through the UNO board to the PC for display. An LED should also be turned on to indicate that the triggering conditions are met. For the time being, the triggering condition is whether the FPGA push-button is pressed. (2)The UNO board would flash an on-board LED at 0.5 Hz (1 second on and 1 second off) continuously and forward the sequence of data from FPGA to the PC. It stops flashing after the data have been sent to the PC. (3)It may be better to store/send/display one channel of accelerometer data first. Completed till phase 2 need to do phase 3 NOTE: We only have to get datafrom accelerometer and send to uno, we already completed code to draw waveform. Just try to get data for x-axis and save in memory and send to uno. If done correctly, this should be enough. No need to fix all axis PS: You might need TV to help me install it if it has errors
项目 ID: 22632932

关于此项目

3提案
远程项目
活跃4 年前

想赚点钱吗?

在Freelancer上竞价的好处

设定您的预算和时间范围
为您的工作获得报酬
简要概述您的提案
免费注册和竞标工作
3威客以平均价$33 AUD来参与此工作竞价
用户头像
FREELANCER RECOMMENDED ------------------------------------------------------ Can help... I am a Fullstack Expert in development of web, desktop and mobile apps... Lets Start! Please start a Discussion with me and we can get started from there... Please check the past projects I have handled and check my reviews for what employers have to say about my work... Can start right now...
$20 AUD 在7天之内
5.0 (9条评论)
4.4
4.4
用户头像
your project is interwsting but your budget is very low. I can work on your project as i am an experienced embedded developer. please ping to discuss further.I guarantee you best service and timely deivery
$55 AUD 在7天之内
4.9 (16条评论)
3.2
3.2

关于客户

NIGERIA的国旗
Agbado, Nigeria
4.6
86
付款方式已验证
会员自5月 11, 2017起

客户认证

谢谢!我们已通过电子邮件向您发送了索取免费积分的链接。
发送电子邮件时出现问题。请再试一次。
已注册用户 发布工作总数
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
加载预览
授予地理位置权限。
您的登录会话已过期而且您已经登出,请再次登录。